|

[2023] How to Reset Samsung Remote? (Must Try)

Sharing is caring!

How to Reset Samsung Remote? There are various reasons why your remote control may not function properly.

Physical damage, battery issues, pairing issues, and problems with the infrared sensor on the remote or television are the most typical problems.

Popcorn with TV remote controler: How to Reset Samsung Remote
How to Reset Samsung Remote

And if it doesn’t work when you try to use it on your television, you can run a short test to determine whether the problem is with your remote or your television.

How you troubleshoot your remote is dependent on the problem you’re experiencing with it.

You may have a filthy set of controls on your television if your television appears to be hitting buttons all by itself.

Quick Tip to Try!

To reset the remote, follow these steps: Remove the batteries from the remote. Press the ‘Power’ button for 8 seconds to reset the remote. Reinsert the batteries. Try using the remote again.

If you need help accessing the battery compartment or have any other questions about the reset process, you can refer to the user manual for more information.

Other Related Articles:

How to Reset Samsung tv Without Remote

How to Get Peacock on Samsung Smart Tv

Where is The Camera on Samsung Smart Tv

Popcorn with TV remote controler
How to Reset Samsung Remote

How to Reset Samsung Remote Programming?

You may need to reset a Samsung TV remote to alter the device that it is preset to operate.

The remote control of some Samsung televisions may be set to operate other devices, such as a cable box, an audio system, and a DVD player.

Make sure your Samsung remote can operate other devices by looking at the buttons on the top of the controller.

If you notice the CBL, AUX, and DVD buttons on your remote, your remote can be customized to control the devices listed above.

Reset the remote programming by pushing the button for the device you wish to program and then holding down the “Setup” button until the light either blinks or becomes solid, depending on your remote.

You may check to see if your device is turned off or on by typing in the code for your device, pressing the device button, and then touching “Power.”

If it doesn’t work, repeat the process and try another code that was recommended.

Finding the codes for your device can be done by visiting the Samsung support website and checking for the handbook for your specific TV remote.

The Samsung Remote Doesn’t Work

Several factors can contribute to the appearance that your Samsung remote is not functioning properly.

Many of these can be resolved by using troubleshooting techniques.

Recommended:  How to Hide Apps on Samsung Phone? [2023] (6 Steps to Hide it)

If the batteries in your remote are completely depleted, your remote may become inoperable. Replace the remote’s batteries with a fresh set of batteries to resolve the issue.

A malfunctioning Samsung TV remote control may also occur as a result of an electronic flaw in the remote.

Removing the batteries, pressing a button on the remote to drain any leftover power, and then reinstalling the batteries will resolve this issue.

Your remote control should now be fully functional.

Failure of the remote to make contact with the infrared sensor on your Samsung TV is another common cause of the remote not operating properly.

Check to see that no objects are blocking the bottom of the television before attempting to change the channel using the remote.

Is it possible to reset the Samsung Smart tv remote?

The following methods will help you fix your Samsung Smart tv remote if it is not working properly and does not respond when you press the power button.

If you are having trouble getting your Samsung Smart tv remote back up and running, you can try the methods listed below to get it back up and running.

Let’s have a look at it in more depth below.

How to Reset the Samsung Smart TV Remote Control?

Step 1: Get a hold of the Samsung smart television remote control.

Step 2: Disconnect the batteries from the Samsung smart television remote.

Step 3: Press and hold the power button for ten seconds to complete the process.

Step 4: Press and hold the power button for 10 seconds, then remove the batteries from your Samsung smart tv remote control and replace them.

5. Turn on your Samsung smart television and use the remote button to direct your remote directly to the Samsung smart television.

6. And that’s it; that’s how you reset your Samsung smart television.

This method of performing a power reset on a Samsung smart tv is effective for all models.

What is the purpose of resetting the Samsung smart tv remote?

If your remote stops responding all of a sudden, or if simply the power button or the source button is not responding when you push them, you will need to reset Samsung Smart tv remote working and then try one of the other Samsung remote troubleshooting methods once you have reset Samsung tv remote.

Before purchasing a new Samsung Smart tv remote, reset the old one.

A large number of people, including the majority of Samsung smart tv customers, will be under the notion that if the remote buttons do not function, you will need to get a new remote control device for your Samsung smart tv.

If the power reset Samsung smart tv remote option does not work, you should try another method of repairing your Samsung remote, such as cleaning it properly.

If the power reset Samsung smart tv remote option does not work, you should consider purchasing a new Samsung remote control device.

The most effective methods for resolving Samsung Smart TV remote issues

There are a variety of reasons why your Samsung Smart TV remote may have stopped working, ranging from the blatantly obvious to the downright obscure.

We’ve compiled a list of some of the most common causes of this issue for your convenience.

For starters, here is a manual for the Samsung smart remote control, which will offer you thorough instructions on how to operate your remote.

1. Confirm that your network is operational.

This can be a good beginning point because your Smart TV or remote will never function properly if you do not have a reliable Internet connection.

Besides, plugging things in and out is never a bad thing, so let us give it a shot.

  • Unplug your modem, router, and television.
  • Wait for approximately 1 minute.
  • Reconnect them with the wall sockets.
Recommended:  What Samsung Phones Have Wireless Charging? [Revealed]

2. Download and install the remote control application.

However, if you are able to operate your television from your smartphone without encountering any difficulties, you can proceed to the next stage of addressing the problem with the TV software.

3. Purchase a new WiFi module.

It is usually found coupled to the power button and infrared sensor, and it has the potential to be the source of the problem.

As a result, when the WIFI module is not functioning, the television appears to be trapped in a state of waiting for the network to respond.

They are quite inexpensive, costing less than ten dollars, and can assist you in pairing your remote with your Samsung TV.

Replace it with the new WiFi module and, after reassembling everything, perform a factory reset on the television.

4. Clean the infrared sensor/remote control unit.

This solution is completely free and can be installed in a matter of minutes.

Simply blow on the sensor’s terminals and the cable that connects to the board; if they become dusty, the sensor may not be able to receive the signal properly.

(See also: It is possible to use the same procedure with the sensor on your remote to ensure that it is clean and ready to operate.

5. Replace any depleted batteries.

We did mention that some of them were quite obvious, and it doesn’t get much more evident than a battery that has gone flat.

If your remote isn’t working, the first thing to check is whether or not the batteries are running low on power.

The quickest and most straightforward method is to use another set of batteries in your remote that you are confident are okay.

6. Confirm that the remote is paired.

We understand; the remote was previously paired; why wouldn’t it be paired again now?

In the age of technology, things like this may, unfortunately, and do happen.

If you’re perplexed as to why your remote isn’t working and you’ve ruled out the possibility that the batteries are the problem, it’s worth checking to see if the remote is still paired to the TV.

For approximately 5 seconds, press and hold the Return and Play/Pause buttons together.

Your TV will begin to sync with the Smart Remote at this point.

7. Make sure your television’s software is up to date.

Because it takes two to tango, it’s possible that the problem is not with your remote, but with your television.

It is possible that an issue with the TV’s software will arise; thus, we should rule this possibility out by seeing if there is anything that needs to be done.

Although the procedure may alter from one television show to another, the following is a typical guideline.

  • Go to Settings/All Settings/Support and select the appropriate option.
  • Select Software Update from the drop-down menu.
  • Select Network from the drop-down menu. If this step is not available, you can skip it.
  • To install the update, select Yes/OK from the drop-down menu.

8. Confirm that there is no interference.

On a Samsung Smart TV, your remote should be able to communicate with the television through Bluetooth; however, if you have an infrared remote, ensure sure there are no obstacles between the remote and the television receiver when you are using it.

9. Restart the television.

Problems can arise with any sufficiently intricate software from time to time, particularly if the software has been in use for extended periods of time without being reset.

The software that controls the “smart” portion of your Smart TV is also prone to this type of problem, so it may be worthwhile to perform a hard reset on it before concluding that your remote or TV is malfunctioning.

Recommended:  How To fix Prime Video Not Working On Sony TV? (6 Easy Solutions!)

You can accomplish this by simply turning off the television and unplugging it for a minute or two.

When attempting to determine the source of a problem, this is typically a useful beginning point.

  • Continue to press and hold the power button on your remote control for approximately 5 seconds, or until the television turns back on.
  • If the problem persists, unplug the television from the wall completely and try again. Then press and hold the power button on the television until it turns off.
  • After 2 minutes, reconnect the power cord to the television.

10. Invest in a universal remote control.

Even if it may seem strange, an original TV remote control can sometimes be the source of all the drama.

Consider purchasing a new remote control, ideally a universal one, which may be of assistance and is only a few dollars.

Key Takeaway: Reset Samsung Remote

To reset the remote, follow these steps:

  1. Remove the batteries from the remote.
  2. Press the ‘Power’ button for 8 seconds to reset the remote.
  3. Reinsert the batteries.
  4. Try using the remote again.

Our Final Thoughts

We hope the solutions have solved your issue. Samsung’s smart TV remotes offer a plethora of convenience at your fingertips, but when they stop working, it’s obviously frustrating.

However, while hardware failures are not impossible, errors of this nature are frequently the result of a relatively fixable problem that does not necessitate the purchase of a new remote or attending an expert.

It is important to remember to take your time and cover all of the possible possibilities since you can be certain that if you skip over one potential defect, it will be that flaw that causes the problem.

Frequently Ask Questions

Why is my Samsung TV not responding to the remote?

However, the most typical causes of a non-functioning TV remote include a battery, pairing, and infrared sensor problems. Press the power button on the remote control while pointing it at the television. Ensure the LED indication on the television is blinking. If not, your remote’s batteries do not have sufficient juice remaining.

How can I sync my Samsung remote control?

The remote control sensor is often found on the lower right side of Samsung televisions. If not, it is in the bottom center, exact. Next, for at least 3 seconds, simultaneously press and hold the Play/Pause and Return buttons. The Smart Remote and Smart TV will start synchronizing.

Why won't the remote control work with my Samsung TV?

The most frequent causes of a broken TV remote are battery, pairing, or infrared sensor problems. Pointing the remote control at your TV, press the power button. On the TV, check to see if the LED indication blinks. If not, the batteries on your remote do not have enough charge.

How can I get the remote for my Samsung Smart TV to work?

Follow the steps below to reconnect your Smart Remote to your Samsung Smart TV:
Direct the Smart Remote at the TV’s remote sensor.

Press and hold the return key as well as the play/pause buttons simultaneously for three seconds.
The Smart Remote and your TV will now start synchronizing.

Author

  • Trevor Eason

    I am Trevor Eason an entrepreneur, a designer, web developer, and software engineer currently living in Dallas, TX. My interests range from technology to photography. I am also interested in entrepreneurship, gaming, and basketball. I run my own Tech Win Reviews blog. Hope you will join me for all your Samsung and Tech Reviews and recommendations.

Sharing is caring!

Similar Posts