[2023] How to Reset Samsung Dryer Control Board? (Quick Fix)

How to Reset Samsung Dryer Control Board? When something goes wrong with your dryer, such as when it displays an error number or when it is not turning on, spinning, beginning, or heating, you may believe that all that is required is a good reset.

However, this is not always the case. In many cases, strange electronic malfunctions (such as those that may occur after a power loss) can be resolved with a simple reset, but if this does not successfully restart the dryer, further troubleshooting will be required.

However, depending on the problem you receive, it may or may not be a good idea to restart your computer at the first hint of difficulty.

Troubleshooting: Issues on Samsung Dryer Control Board Troubleshooting

Issue	Solution
Dryer is not turning on	Unplug the dryer from the power outlet for 60 seconds, then plug it back in.
Reset samsung dryer not heating	Check the lint screen and exhaust duct to make sure they are clean. If they are clean, try resetting the dryer control board. To do this, unplug the dryer from the power outlet for 60 seconds, then plug it back in.
Dryer is not drying clothes	Check the dryer settings to make sure they are correct. If the settings are correct, try resetting the dryer control board. To do this, unplug the dryer error codes from the power outlet for 60 seconds, then plug it back in.
Dryer is making strange noises	Check the dryer for any loose or damaged parts. If you find any loose or damaged parts, tighten or replace them as needed.
Dryer is displaying an error code	Refer to the dryer’s owner’s manual for the meaning of the error code. If you are unable to resolve the issue, contact a qualified technician for assistance.

To discover how to reset your computer, when it is appropriate, and what to do if a reset does not work, continue reading this article.

See Also:

Quick Guide on How to Replace Heating Element in Samsung dryer

What does UR mean on Samsung washer?

What you need to Know About Samsung Washer Warranty

How to Reset Dryer Control Board?

You must first turn off the power at the circuit breaker, or you may unhook the dryer from the wall socket and leave it out for a period of time to successfully reset your Samsung dryer.

While no electrical current is running into the dryer, you should wait for the electrical charge to dissipate before continuing.

You can wait up to 5 minutes before plugging in the dryer and turning it on so the electrical current can begin to flow back into the device.

The control board of your Samsung dryer is in charge of all of the dryer’s activities and is used to regulate the unit’s temperature and drying time.

First and foremost, you must have received an error number from your Samsung dryer; the dryer has a variety of error codes that each represent a different problem that the dryer is now facing.

Resetting some error codes can clear them; however, troubleshooting other problem codes will need to be performed.

The most common Dryer control board problem codes, as well as the ways to troubleshoot them

Because the classic Samsung Dryers do not typically have a digital display, the error codes will be displayed as blinking lights when an error occurs. The following are the fault codes that may be displayed on digital displays for units with digital displays.

Error Codes for the Temperature

If you see any of the trouble codes listed below in your display, the dryer’s temperature sensor or the sensor that measures the temperature is malfunctioning or has failed.

These are the codes that were used: (tS, tE, t5, tCS, tC, tO, t0, 1tC5,tE3, tC5, 1 tC, 1tCS).

Any of the following codes on your Samsung dryer indicate that the lint screen or the vent system is clogged, causing heat to be trapped inside your dryer error codes and causing it to overheat.

Depending on the nature of your problem, cleaning the lint system or the vent may be necessary, or you may choose to do so in combination with cleaning the other two.

Error Codes for a Button That Has Jammed

If the dryer’s control panel identifies a button that has become stuck or that has been constantly pressed, the following error codes will appear (bE, bC2, bE2, 6E, 6C2, 6E2).

If your dryer displays any of the following problem codes, you will need to turn it off and then press each of the buttons on the dryer’s control panel individually to allow them to be removed from the dryer’s control panel.

In doing so, make certain that you reach the edges of each button on the way down.

After that, you can turn on the dryer and check if any codes come back.

If they do, you will need to contact Samsung to have them look into the problem.

Error Codes in the Heating System

The following dryer error codes are likely to be shown if your Samsung dryer becomes overheated on several occasions (HC, 1 HC, hE, HC4).

This mistake is most likely caused by a blocked dryer error codes vent or lint screen system that traps heat in the dryer.

To remedy this dryer error codes, you must clean the vent system or the lint screen; you may even clean both if you want to be absolutely certain that the problem has been resolved.

Codes for Communication Errors

These error codes will be shown when the internal components of your dryer are unable to interact with one another (AC, Et, EEE, AE, AE4, E3, AE3, AE5, 1 AC).

Moreover, to get rid of the error code, you must turn off the machine for approximately 60 seconds before turning it back on.

Codes for Voltage Errors

If the voltage supplied to your dryer is not normal, your dryer will notify you by displaying one of the error codes listed below (9C1, 9E1, 9E, 2E,).

To get rid of the dryer error codes listed above, ensure that your dryer is not operating on an extension code but instead on its circuit.

Individuals who use electric dryers must make certain that the power cord is properly installed and that the device is receiving the proper voltage before utilizing the appliance.

How to Fix a Dryer That Won’t Stop Spinning: Causes and Solutions

First and foremost, it is critical to discover the problem’s source before troubleshooting your Samsung dryer.

Samsung dryer reset

Typically, this type of issue is caused by a simple trip in one of the components on the circuit board, and it can be readily corrected by just resetting the circuit board.

First and foremost, do not be concerned if your Samsung dryer does not switch off.

You do not need to be concerned that your machine is experiencing any type of electrical problem that could be dangerous.

In addition, when dryers malfunction in this manner, they typically continue to tumble but do not emit heat as a result.

This is more of an irritation than anything else, but there is no need to be concerned that it will lead to any sort of more serious or dangerous situation.

To gain access to and reset the circuit board on your dryer, you must carefully follow the instructions outlined below.

Before you begin, you will require either a power drill or a Phillips screwdriver to complete this project.

Disconnect the dryer from the power source

First and foremost, unplug your dryer from the power source for your own safety before beginning this troubleshooting procedure.

Samsung moisture sensor dryer reset

You will also be working on the rear of the dryer, so move your dryer a few feet away from the wall to make it easier to reach the back of the dryer.

Remove the Dryer Control Panel by unscrewing it

You will then need to locate two screws on the rear of your dryer that will connect the control panel on the top of your appliance.

Remove the screws from their sockets with a drill or screwdriver and set them away.

After removing the screws, the control panel will fold forward, allowing it to be removed from the top of your washer.

A few small tabs connect the control panel to the base of the dryer, and you will need to move them about a little bit.

This will allow you to gain access to the circuit board that will be covered while you are working on it.

Remove the Circuit Board Cover from the board

In most cases, after you have taken out your dryer’s control panel, the circuit board cover will be placed on the left side of the dryer.

It will appear as a roughly 8-inch-square box on the screen.

At the bottom of the lid, two tabs can be simply removed to release the box and reveal the PCB, or printed circuit board, within it.

Unplug all of the cords

Following that, you will unplug all of the components from the printed circuit board.

There will be approximately half a dozen different colored cables connected to the board.

These should all be unplugged in any sequence, and in no particular order.

The PCB will be connected to the dryer’s control panel by a cord located outside the PCB.

Remove the cord from the wall as well.

These cords will be equipped with a tab that must be pressed to release the cord from the socket. Pulling the cords without first securing them will result in damage.

Examine the cords for signs of wear and tear

After all of the cords have been unplugged, carefully examine them for signs of damage, especially if your laundry room is particularly damp.

Depending on the amount of rust present, there is a considerable potential that your dryer will not turn off properly, and you may be required to repair the PCB and connections.

If, on the other hand, your cables look to be in fine shape, simply plugging them back in should resolve your issue.

Reconnect all of the cords

You will now rejoin all the cords, as long as none have been damaged.

This can be done in any order at this point.

Make certain that all cords are properly secured back into their respective circuits.

The cords and circuits will be color coordinated so that you can be certain they are reconnected to the correct location after they have been disconnected.

Reassemble the PCB cover and the Dryer Control Panel if necessary.

The PCB cover will be reattached after all of the cords have been reattached to their proper locations.

Replace the control panel on the dryer by first putting it into the machine and then screwing it back into place with the screws that were previously used to secure it. Finally, make sure your dryer is connected to a power source.

Other Tips for Troubleshooting

It is possible that a basic reset, such as removing your dryer from its power supply for 10-15 seconds and then plugging it back in, will be successful before attempting to reset the entire circuit control board dryer.

Additionally, performing routine maintenance and cleaning of your dryer is always advisable.

Samsung dryer not heating reset

In order to accomplish this, you should always empty the lint filter, vacuum out your dryer, clean and upgrade your vent hose as needed, and clean the external dryer and exhaust vents on a regular basis.

Also, be certain that the loads you are undertaking are of sufficient size and that you are not overloading your equipment.

Performing this type of routine maintenance and care on a regular basis will hopefully prevent future problems with your dryer.

How To General Reset Your Dryer?

Samsung dryer reset button on the dryer’s control panel, which can be used to restart the machine.

1. Allow the dryer to cool for approximately 10 minutes if the motor would not start.

2. After that, press the reset button. If there are no motor, switches, or electrical system problems, this should be sufficient to restart the drying machine.

Aside from that, how can I perform a diagnostic on my dryer?

• Perform a vent blockage test to determine the cause of the problem.
• Check to see that the drum is empty before closing the door.
• Turn on the dryer by pressing and holding the POWER button for 5 seconds, then press and hold the Adjust Time Up + Dry Level button until InS or In shows on the display.
• To begin the Vent Blockage Test, press the START/PAUSE buttons for about 2 minutes to initiate it.

A second inquiry concerns if the Samsung dryer can be re-programmed.

You might try unplugging the dryer for 5 minutes and then plugging it back in to see if that helps to reset the control board dryer.

This can be useful if the control board dryer has been stuck due to a power surge or glitch encountered while operating on the electric supply lines.

Samsung Dryer No Power To Control Panel

If your Samsung dryer is not powering the control panel, try these troubleshooting steps:

1) Check if the power cord is properly connected.

2) Reset the circuit breaker or replace a blown fuse.

3) Ensure the outlet is functioning by plugging in another device.

4) If issue persists, contact Samsung customer support for further assistance.

What caused my dryer to quit functioning?

If the switch does not provide continuity, it should be replaced.

The driving motor rotates the drum and the blower wheel, which exhausts the air via the system.

Before replacing the motor, ensure that the thermal fuse, the start switch, and the door switch are all working properly.

It is possible that the switch will fail and the dryer will lose power, even though the belt is not broken.

Key Takeaway: How to Reset your dryer?

Resetting a dryer is simple. Unplug it (or turn off the power at the circuit breaker), wait for the electrical charge to leave the dryer (typically between 1 and 5 minutes), and then plug it back in.

Our Final Thoughts

There are times when your Samsung dryer may be experiencing more severe issues, and resetting and troubleshooting will not be enough to get it back to working correctly; in this instance, you will need to contact the Samsung support department.

Because if you make numerous unsuccessful attempts to clear the error codes, you will simply make it more difficult for the expert to diagnose the problem because you will have erased the history of dryer error codes.

Frequently Ask Questions

Question	Answer
How to reset my samsung dryer control board?	To reset your Samsung dryer control board dryer, unplug the dryer from the power outlet for 60 seconds, then plug it back in. This will clear any dryer error codes that may be causing the dryer to malfunction.
What if my dryer still won’t work after resetting the control board?	If your dryer still won’t work after resetting the control board dryer, there may be a more serious problem with the dryer. In this case, you may need to contact a qualified technician for assistance.
What are some common problems with Samsung dryers?	Some common problems with Samsung dryers include:

Why is my Samsung dryer turning on but not starting?

If the dryer’s light is on but it won’t start, ensure the door is closed and fastened securely. The drying cycle will not begin until the door is closed and the latch is engaged as a safety measure. To engage the latch, firmly close the door and ensure that loose clothes is not impeding its closure.

How do I reset the board in my dryer?

Reset the dryer.

Your dryer can be reset with ease. When the dryer’s electrical charge has cleared (usually 1 to 5 minutes at most), unplug it (or turn off the power at the circuit breaker), then turn it back on. I’m done now. All it takes to reset is that.

How do I check my dryer's diagnostics?

Once the dryer has been turned on by pressing POWER, press and hold Adjust Time Up + Dry Level for 5 seconds or until InS or In appears on the display.

How is an electronic control board for a dryer tested?

The rotary switch on your dryer can be tested by unplugging it and removing the top control console panel to reveal the switch. Put the probes on the switch’s terminals and set your multimeter to the Rx1 setting. You ought to get an infinite reading.